Wiki 9Minecraft Wiki 9Minecraft

The community wiki and guide for Arcanism — guides, recipes, items and mechanics.

Contents (6)
  1. Guides
  2. Items
  3. Blocks
  4. Mobs
  5. Configuration
  6. Frequently asked questions

Guides

Step-by-step, in-game.

Items

111 items · showing 24. Browse all →

View all 111 items →

Blocks

Mobs

Creatures this mod adds.

Spell Entity

Configuration

Every setting in the mod config file, with what it changes.

OptionWhat it does
break_energy_per_hardnessBreak Energy Per HardnessMana cost (J) per point of block hardness
cast_massCast MassFixed mass (kg) used in spell mana cost calculation
client_side_interpolationClient-side InterpolationInterpolate server data on the client. Enabling this does not change the server's sync timing, it only smooths values at the cost of latency
disable_animationsDisable AnimationsDisables animations
fuel_value_multplierFuel Value MultiplierFuel heat value corresponding to each tick of burn time
gameplayGameplay
global_cast_cost_multGlobal Cast Cost MultiplierGlobal multiplier applied to all spell mana costs
client_interpolation_windowInterpolation Time WindowTime range (ticks) over which server data is smoothed
more_balanced_fuelMore Balanced FuelMake fuel heat values closer to real-world values
networkNetwork
server_data_sync_intervalServer Data Sync IntervalSync interval (ticks) for most server data (machine mana/work progress, etc). May affect network traffic
visualVisual

Frequently asked questions

What is the easiest way to start generating mana?
Place a Solar Panel or Wind Turbine for passive early mana generation without setting up fuel lines. When your factory needs more power, scale up to a thermal setup using a Water Pump, Liquid Heater, Heat Exchanger, and Steam Turbine.
How do I connect generators, buffers, and machines to move mana?
Run Mana Cable along your factory line and use a Basic Mana Connector, Horizontal Mana Connector, or Vertical Mana Connector to hook blocks into the network. Place a Small Mana Buffer, Medium Mana Buffer, or Large Mana Buffer along the route to store surplus mana.
Why did my factory stop running even though my generators still have power?
Arcanism splits magical energy across a four-element mana network, and all four paths must stay balanced for your assembly lines to keep running. If you are running a thermal setup, also make sure a Pressure Relief Valve is installed so excess pressure does not stall your system.
How do I power my RG Alloy Wand and give it more mana capacity?
Fit your RG Alloy Wand with a Mana Cell (Size 1) up to Mana Cell (Size 5) to establish and expand its internal mana pool. You can also install Plugin: Auto Charge for automatic recharging and Plugin: Spell Supply I through V to boost how fast mana feeds into your spells.
How do I fit larger programs into my RG Alloy Wand or improve its casting speed?
Install higher tiers of Plugin: Spell Storage I through IV alongside Plugin: Spell Packer to hold and organize more spell parts. Adding Plugin: Spell Release I through V upgrades how effectively the wand releases compiled spells.
How do I make a custom spell shoot forward as a projectile?
Use Spell: Get View Vector to grab the direction you are aiming, scale it with math operators if needed, and feed that vector into Spell: Gain Velocity on the Spell Entity. Without applying velocity, the spawned Spell Entity will not travel away from you.
How do I make a spell detonate only when it hits a mob or wall?
Place Spell: Trigger on Touching Entity or Spell: Trigger on Touching Block in your spell chain before impact parts like Spell: Explosion or Spell: Apply Potion. This waits until the Spell Entity physically touches a block or mob before firing the payload.
How do I program a spell that mines blocks and brings the drops to me?
Check your target coordinates using Spell: Get Block At Position and Spell: Is Air so you do not waste casts on empty space, then run Spell: Mine Block or Spell: Break Block. Pair it with Spell: Send To Inventory to pull drops straight to you instead of leaving them on the ground.
Why do certain spells suddenly cost massive amounts of mana?
Mana drain is calculated with physics formulas using real-world mass and energy units rather than flat per-part fees. Accelerating projectiles to high speeds or breaking tough blocks drives up the cost based on block hardness and the spell's calculated mass.
How do I make numbers bigger than 9 when programming a spell?
Because number parts only run from Spell: Number 0 to Spell: Number 9, combine them with Spell: Multiplication, Spell: Addition, or Spell: Exponent to reach larger values. Wrap grouped math inside Spell: Left Paren and Spell: Right Paren to control the order of operations.
Can a spell save a position or value to reuse later in the same cast?
Yes, use Spell: Set Storage to save a calculated number, vector, or entity value, and separate multiple instructions with Spell: Expression Separator. Call Spell: Get Storage later in the spell chain to read that saved data back.
How do I build a repeating loop in a spell without breaking it?
Start the block with Spell: For or Spell: Loop Start and always close it with a matching Spell: Loop End. You can insert Spell: Delay to space out iterations over multiple ticks, or pair Spell: If with Spell: Loop Break to exit early when a condition is met.
How can I troubleshoot a custom spell when the math or targeting fails?
Insert Spell: Debug Print after parts like Spell: Get Nearest Entity or vector calculations to inspect the exact values your spell produces mid-cast. This lets you verify coordinates, health checks, and boolean conditions step by step instead of guessing what went wrong.
Can I customize the appearance of my RG Alloy Wand?
Yes, in addition to swapping out modular wand parts, you can install Plugin: Color Theme to customize the visual look of your RG Alloy Wand.
How do I lower spell mana costs or adjust fuel burn values in the config?
Reduce `global_cast_cost_mult`, `cast_mass`, or `break_energy_per_hardness` in the config file to make casting and block breaking cheaper. To tune thermal generators, change `fuel_value_multplier` or enable `more_balanced_fuel` so burn heat aligns closer to real-world fuel values.
How do I fix choppy machine progress bars on servers or FPS drops in big factories?
Turn on `client_side_interpolation` and adjust `client_interpolation_window` to smooth out machine gauges without lowering `server_data_sync_interval` and increasing network traffic. If large multiblock lines hurt your framerate, enable `disable_animations` in the visual config.